Acrosser AR-ES6050FLD-W Uživatelský manuál

Revision: 1.0 Revision Description Date 1.0 Release 2012/4/6 AR-ES6050FLD-W User Manual 1

Revision: 1.0 3. Align the notch key on the Mini PCI-e card with rib on the slot. Figure 8 4. Push Mini PCI-e card horizontally . Figure

Revision: 1.0 5. Using two M2 screws to fasten Mini PCI-e card. Figure 10 6. Close the heat sink cover using the original screws to fast

Revision: 1.0 2.3 Installing the DDR2 SO-DIMM procedures 1. Unfasten the screw of the DDR cover and open the cover. Figure 11 2. Align th

Revision: 1.0 3. Push DDR2 SO-DIMM horizontally and make sure it is locked by hooks of two sides of DDR2 socket. Figure 13 4. Recover the

Revision: 1.0 2.4 Assemble/Disassemble the DIN mounting bracket. 1. Hook the spring of the DIN mounting bracket onto the upper of DIN rail. Fi

Revision: 1.0 3. Make sure they are locked together. Figure 16 4. Disassemble the DIN mounting bracket of AR-ES6050FLD-W system. Press dow

Revision: 1.0 Appendix. Cable Pin Define 1. Com cable 110mm 2. Power Cable BLACK BLACK YELLOW YELLOW 16

Revision: 1.0 3. Switch Cable 17

Revision: 1.0 3 AR-B6050 Board Guide 3.1 Block Diagram 18

Revision: 1.0 AR-B6050 Board Specifications  Intel Atom N450 1.66GHz  Intel Graphics Media Accelerator 950  1 x SO-DIMM supports DDRII up

Revision: 1.0 2 Contents 1 ... 3 Introduction to AR-ES6050FLD-W1.1 Specifications...

Revision: 1.0 3.2 AR-B6050 H/W Information This section describes the installation of AR-B6050. At first, it shows the Function diagram and the l

Revision: 1.0 3.2.2 AR-B6050 LAYOUT (Bottom side) JP1 COM1 VGA1 ATX1 COM2 J1 BAT1 SATA2 USB3 SYSFAN1 SATA1 USB1 CN2 CN4 USB2 CN3 J

Revision: 1.0 3.3 Components and Jumps Setting List 1. JP1: LCD panel driving voltage selection. 2. ATX1: AT power input connector. 3. BAT1: CM

Revision: 1.0 10. COM1: RS232 signal connector for port #1. 11. COM2: RS232 signal connector for port #2. 12. SATA1: SATA device connector #1.

Revision: 1.0 19. VGA1: D-SUB-15 female connector for VGA output. 20. J1: CMOS data clear 21. USB3: Internal USB2.0 connector D-SUB-15 female

Revision: 1.0 27. DIMM1: DDR-II SODIMM Socket. 28. CF1: Type-II compact flash card socket. DDR-II SODIMM Socket. +3.3V CF card only and UDMA

Revision: 1.0 3.4 BIOS Setting The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS. To activate the BIOS

Revision: 1.0 3.4.1 Main Setup Once you enter the InsydeH2O BIOS™ Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to hi

Revision: 1.0 Cache RAM N/A This field displays the cache ram of the CPU. Total Memory N/A Displays the total memory available. SODIMM 0 N/A T

Revision: 1.0 3.4.2 Advanced Chipset Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields

Revision: 1.0 1 Introduction to AR-ES6050FLD-W AR-ES6050FLD-W is a fan-less embedded system that could be used by DIN mount for factory uses, VESA

Revision: 1.0 3.4.3 Security Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you ca

Revision: 1.0 Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set

Revision: 1.0 3.4.4 Boot Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can pr

Revision: 1.0 3.4.5 Exit Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can p

Revision: 1.0 3.5 WATCHDOG, GPIO, AND BYPASS PROGRAMMING 3.5.1 Watchdog Programming This section describes the usage of WATCHDOG. AR-B6050 integ

Revision: 1.0 ======= //=========================================================================== // Language include files //=================

Revision: 1.0 outportb(IO_Port_Address,0xF5); // Select Watchdog count mode seconds or minutes outportb(IO_Port_Address+1,0x02); // Def

Revision: 1.0 3.5.2 GPIO Programming This section describes the usage of GPIOs. AR-B6050 integrated eight bits, 5V TTL level, bidirectional, and

Revision: 1.0 //=========================================================================== // Main procedure //==================================

Revision: 1.0 outportb(IO_PORT_BASE,0x07); outportb(IO_PORT_BASE+1,0x07); // Set GPIO Port Active outportb(IO_PORT_BASE,0x30); outport

Revision: 1.0 1.3 System Dissection (1) Dimensions (2) Front Panel USB 1~4 Antenna hole Audio LAN 1~2 Power switch Termin

Revision: 1.0 if(result) Show_Fail(); else Show_Pass(); return result; } //=====================================================

Revision: 1.0 // Function : Show_Pass() // Input : - // Change : - // Return : -

Revision: 1.0 3.6 GPIO and Watchdog 3.6.1 Overview This model provides both a GPIO interface and a Watchdog timer. Users can use the GPIO and W

Revision: 1.0 3.7 API List and Descriptions 3.7.1 GPIO 1. Syntax: Status_t getGpioCapability(uint32_t *pInputs, uint32_t *pOutput )

Revision: 1.0 uint32_t Direction; status = getGpioDirection(GPIO_ID2, &Direction); if(Direction == 0x1) { cout << “GPIO2 is an Input

Revision: 1.0 45 Status_t setGpioLevel( uint32_t Id, uint32_t Level ) Description: Set the current state of GPIO ports. Parameters: The

Revision: 1.0 (3)System Configuration 3 2 4 89101112135 6 1 7 5

Revision: 1.0 Item Description Quantity1 LEFT COVER 1 2 PCI-104 CARD 1 3 DIN MOUNTING BRACKET 1 4 PCI-104 TAIL CONNECTOR 1 5 BASE 1 6 AR-B

Revision: 1.0 2 Procedures of Assembly/Disassembly 2.1 Installing the CF card 1. Unfasten two screws of CF bracket and then take out the CF ca

Revision: 1.0 3. Push CF card to the bottom of bracket to stop the forwarding at the bend of bracket. Figure 4 4. Push them into the CF s

Revision: 1.0 2.2 Installing the Mini PCI-e interface card 1. Unfasten the six screws to take out the heat sink cover. Figure 6 2. May